Відео

Thank you for the video very simple and easy explanation. I am having the same problem right now. I will be disassembling the unit and checking for sudden blockage. Hopefully that fixes the issue you probably just saved me about $1500 at the dealer.

Watched the video specifically for torque specs 😒

Those trucks are total trash

Did you know the part # for the seal and gasket..? ( water pump thermostat) Thanks.

The title of the video is how to replace this sensor not how to diagnose how they work and what color the fucking sky is

Have you had any experience with LS tractors and issues with egr valves.?

Let me cleaner you and make you smart. Don’t wast your money on maintenance. It cost you a lot of expensive.. if you have this code spn 4364 fmi 18. Just just keep your nox outlet sensor out. You have check ligh on. But it’s work great. If that doesn’t work. Just go buy one box new not ramanufacture. It’s cheap only $6500 all sensor. $1500. Check my video I I hack my system 😂. It’s better then spend every day money. You will be good until 400000 miles

Thx

I’m leaking from the clamp closer to the turbo (2019 Cascadia) replaced seal and clamp 3 times and it still leaked causing smoke when burning off. This time I put new exhaust pipe, new exhaust manifold piece that 7th injector is bolted to , new 7th injector (injector housing, injector and seal) and new clamp and seal AGAIN! after all that it STILL LEAKED!!

Dealing with a similar issue on a Mercedes 906la motor but the pump and metering valve switching valve are exactly the same. Spn 4334-18 Replace pump and metering valve and flushed lines still no luck going to check voltage at pump I know I have 24v there on 1 pin need to check the other. Also I did have oil in air line so going to check that line.

Thanks u Sr

How many miles can it go with out getting serviced though

Do you have a video on replacing these leaking orings I keep hearing about? Its when the whole unit is usually covered

Sorry if I missed it, but did you say which orientation it should be? I.e does “steeper angle” side sit on muffler side or dowpipe?

❤❤❤❤❤❤❤

Informative....

How the hell do you stop the flow of Def after you disconnect those lines?

Never done it but thinking of doing it

Will this work for 2011 Ram 3500 ??

Great video

Beautiful

I’m just going to build a custom set up using a hot water heater, collection drums, filters, etc. And make sure it’s legally disposed off. Haven’t done any reading on exhaust particulates disposal.

Thanks

Soneone brainless Idiot created and other idiots made it 'must have it\

I install a large tiewrap loosely around the dpf to use as a handle along with a pry bar to support the dpd when manuvering the dpf into place.

My truck engine light 570 miles

I’m having Issue with that code SPN 3058 FMI 10, I just replaced the VPod and the Delta P Sensor would it need to be recalibrated?

Who the fuck in there right minds would buy a modern diesel car. They are pure shite please believe me .

Pure common sense .....so many shops out there lack this and then the customer pays the price. Nicely explained

Heating is the best way to clean these.. in an industrial kiln

Great video man short and right to the point

Idiot at the freightliner dealer updated my ECM to the low nix setting.the fvcktard cost me 11 grand in fuel until I figured out what he did .EPA can eat my azz.

Are you doing this in your shop? I don't know what the hot knife method is but I thought that was the only way to clean them.

Why did you stop posting

Excellent content provided. You're much appreciated

Honestly God bless you sir. Thank you for the great explanation and actually understanding that not everything needs to be replaced to find the problem. Every shop I went to want to make me change everything that’s connected to the problem and most of the time it doesn’t even fix the problem and it was something as simple as a wire that was corroded.

When replacing I think you're supposed to pressurize the def inlet to inflate the bladder before attaching the line. 90 psi for 3 seconds is what I've seen....

what scanner do you use ?

Yes it does worked.done this past wknd,with some Awesome. Cleaner from Dollar General..

I cleaned mine with a air hammer and rubber mallet a few days ago. Now it’s so clean you can see right through it. Amazing.

Will this work with the SCR filter?

While driving, I would hear a relay click and all switches ( mirror heater, utility lamp,rest in that row), including hvac, are dead. Later on, relay clicks again, and power is back on.

Nope not to be done it will be replaced after this procedure. Cummins does not recommend

The pump freezes because people overfill their DEF tanks. When the truck is shut off the DEF pump runs in reverse to push any DEF in the pump and lines back into the tank. If the tank is overfilled the return line will freeze and the DEF is not able to be pushed out of the lines and pump. Shut the truck off with DEF still in the pump and lines and it will freeze and expand, splitting the pump and lines. Fill to the bottom of the filler neck and stop. When filled to the bottom of the filler neck it will indicate as "full" on the dash. Don't keep topping it off over and over because anything above the bottom of the filler neck likely will not melt with the heating circuit in extreme cold. I've done thousands of DEF pump and level sensor warranty claims, many of which Volvo could have denied as owner error for filling the tank past "full." Yes, it's a flawed design with the heating loop not melting the top few inches of the tank, but it's the reality for Volvo owners.

How about Test strips for contaminated government bureaucrats ???

Exactly what the problem was. One port flowing freely, the other completely blocked . Removed the plug , cleaned the port . Now flowing properly and performing correctly. Thanks for the tech advice. 👍

Delete your own DPF, save $$$...

Hi does this method also apply to Mitsubishi Pajero DPF? Thanks

@TheDieseler I want to thank you for the Contant and information provided in your videos. I also had a question about whether you’ve had any luck cleaning SCR’s. Thanks

Propane torch burn from low stream end, then flush water from low stream end to upper end.